SmugMug
Home  Login  Help  
 
 View Cart
David  > Electronics > 2-Way Speakers and Cabinets
Gallery pages:  1  2  >  
< 4 of 12 >
David > Top has since been covered with Mahogany venner from Woodcraft, to cover the end - grain, and stained with ZAR Rosewood.
David > Front has since been covered with 1/8" 5 - Ply Aircraft Birch Plywood, and painted flat - black.
David > Same as above ; different angle with the light.
David > Front. All screws are # 12 Brass, 2 1/2" or 3". Left in to provide mass / stiffness to the sides / top + bottom. Kind of like re - bars in Concrete !!
David > Same as above, but on black velvet !
David > Rear. Port and Terminal Block from PE. Just an accident , but note the grain - pattern on the side : Doesn't it look like sound - waves fanning - out from a point beside the Terminal - Block ?
David > Three holes in the side are for dowel cross - braces. 5/8" diam Three of them = one square inch ; ( almost. ) Holes very slightly tapered. Ends of dowels cross - wedged at the time they were glued in.
David > Bottom / Top. 3/4" MDF on the inside of front and back. A lady / Pilot friend sold me a half - sheet of veneered Birch plywood for $ 20. All the MDF I needed came from a piece about 6' or 8' tall and 12" wide, from Lowes. Had a half - round on one edge. Cost just $7 ! The tan - colored MDF on the inside, is glued and screwed to the outer - plywood with six , # 12 x 1 1/4" brass screws. Should be there forever !!
David > Tweeter crossover. Crossovers were built on separate boards, because, due to all my by - pasing etc., it seemed too crowded on one board !! BUT, I couldn't stack them on the bottom, because no matter which way I layed them, the coils ended up on top of each other ! So, I put one on each side. Held down with glue, and 8 brass screws, as large as the peg - board holes would take. They aren't going anywhere ; but, if I want to " Tweak " , I have to do all soldering through the Woofer Hole !
Front. All screws are # 12 Brass, 2 1/2" or 3". Left in to provide mass / stiffness to the sides / top bottom. Kind of like re - bars in Concrete !!
> Front. All screws are # 12 Brass, 2 1/2" or 3". Left in to provide mass / stiffness to the sides / top + bottom. Kind of like re - bars in Concrete !!
Front. All screws are # 12 Brass, 2 1/2" or 3". Left in to provide mass / stiffness to the sides / top bottom. Kind of like re - bars in Concrete !!
Camera: Fujifilm (Finepix 3800) |
More details: exif |
Original size: 960px x 1280px |
Current: 225px x 300px |
Other sizes: Small • M • L • O • save photo |
Share photo: links, forums, blogs |
Keywords: construction pass air cabinets mdf core speaker davewebberspeaker passive mdf cabinets passive crossovers crossovers air core inductor inductor by pass capacitors capacitors hi fi speaker construction
Gallery pages:  1  2  >  
< 4 of 12 >

Comments

| hide gallery comments |

New comment: Requires approval

Name: Email: Link:
Connect  Connect with Facebook


Comment on: | Rating: stars
To foil spammers, enter this code: copy this text in this box: Code unreadable?

Add Comment Cancel

News | Browse | Keywords | Communities | Forum | Wiki | ClubSmug | Prints & Gifts | Shopping Cart | Login
Terms | Privacy | About Us | Contact SmugMug | Blogs | API | Affiliates | © 2010 SmugMug, Inc.
Show FeedsAvailable Feeds | What are feeds?
Gallery Photos:
Atom FeedAtom | RSS FeedRSS